The bent-over row pulls a barbell towards your torso while you hold a forward lean. Both arms row, while the hips, legs and trunk keep the starting position steady. There is no chest pad: being able to maintain that position matters as much as moving the bar.
Written tutorial by SG Home Wellness. Setup, finishing steps and modifications also draw on the supporting sources; the clip may not show each of these actions.
Before you move
Equipment Barbell and suitable plates, Collars when required by the bar and gym rules, Clear lifting space; suitable rack supports if using a raised pickup.
Also called Bent-over barbell row, Overhand barbell row.
Clear room for the bar, your stance and the planned set-down. Choose a bar you can collect, hold and return under control. An empty full-size bar can already be demanding; a lighter training bar is an option. Secure matched plates according to the equipment and gym instructions.
For a raised pickup, ask staff to identify suitable rack supports and confirm both sides are at equal height and locked. The bar must rest securely before you grip it. For a floor pickup, first know how to lift that bar from its actual height; do not turn an unfamiliar floor lift into the start of your rowing set.
Take an overhand grip with the thumbs around the bar, a little outside your legs. Stand steadily with the bar near the thighs. Move the hips backwards and incline the torso forwards, keeping a modest knee bend. This hip movement creates the lean; folding the neck or rounding down to reach the floor is not the aim.
Choose a lean you can maintain while the arms lengthen and the bar clears the knees. Keep pressure through both feet, look towards the floor ahead and keep the neck following the trunk. Rehearse with little load before deciding how far the bar should travel.
How to do the movement
Settle the hanging bar
Let the arms reach down from the shoulders with the bar beneath you. Gently tighten around the waist enough to keep the trunk from rocking, while continuing to breathe. Begin from a still bar rather than a bounce.
Pull towards the torso
Draw both elbows backwards and bring the bar towards the lower ribs or upper abdomen along a comfortable path. Breathe out through the pull. Keep the same hip position instead of standing up to meet the weight.
Finish before the lean changes
End the pull where the elbows can move back without the chest suddenly lifting. Bar-to-body contact depends on grip, proportions and torso angle; it is not a reason to jerk the final part.
Lower into the same start
Straighten the elbows smoothly and guide the bar down. Allow the shoulder blades to move with the reach. Keep the bar clear of the knees, then begin the next repetition only once the lean is steady again.
Finish and get out of position
Lower the bar under control, then return upright with the bar close if that is the pickup method you rehearsed. Replace it onto both approved rack supports, or use your practised floor-lowering method. A sudden drop or twisting reach is not the planned finish.
Keep your hands on the bar until both supports or the floor have taken its weight and it cannot roll. Rest before unloading, and remove plates with the bar stably supported. Stop the set early enough that the return is still manageable.
Exercise reference
Keep the key cue
Barbell row — keep the hip lean steady, draw elbows back and return the bar smoothly.
This browser keeps a reminder and link to the full tutorial.
Cues to remember
Hips hold; arms row
Compare your torso angle at the bottom and top. If every pull needs a small stand-up, reduce the load or choose a supported row.
Follow both elbows
The elbows travel back as the bar comes in. Folding the wrists or curling the bar towards the face changes the path.
Keep a repeatable reach
Return to a comfortable arm extension without chasing the floor. Record the same grip, lean and start height next time.
Must my torso be exactly parallel to the floor?
No single torso angle suits every row and body. A Pendlay row has a different floor-reset start. For this continuous bent-over version, choose and maintain a comfortable lean that lets the bar travel without hitting your knees.
What to watch out for
The chest rises sharply with every pull
Put the bar down, reduce its load and re-establish the lean. If holding the position is the limiting task, use the chest-supported or hand-supported row tutorial instead.
The bar repeatedly hits the knees
Reset the hip bend, stance and bar path using little load. Keep the knees softly bent without turning the row into repeated squats; do not swing the bar around an obstruction.
Wrists fold or the shoulders jerk up to finish
Keep the hand in line with the forearm and stop the pull earlier. A shorter smooth pull is preferable to adding a last-second wrist curl or shrug.
Make it easier or build from this version
Record total bar weight, grip and pickup height. An unsupported row need not replace a supported row, and neither has to lead to a heavier floor-reset variation. Pain, loss of balance or a lean you cannot hold is a reason to stop and reassess the setup.
Make it easier
Lighter bar with the same lean
Reduce the total resistance, including choosing a lighter bar if needed. Keep the overhand grip, planted feet and controlled hanging return. A lighter load still needs a pickup and set-down you can manage.
Chest-supported dumbbell row
This is a different supported exercise. An inclined bench steadies the chest while the arms row; use its full setup rather than leaning on an improvised object.
Add work only within your programme while the torso angle and return remain consistent. Finish when the lean begins to change, even if the arms could jerk another repetition.
Use a manageable barbell increase
Keep the same grip and start height. After a suitable increase, recheck the pickup, still start and controlled set-down; a bigger number does not justify a more upright heave.
What can differ
An underhand grip changes forearm position and arm contribution. A Pendlay row rests the bar on the floor between repetitions. A chest-supported dumbbell row changes the support arrangement and may let you learn the pulling action without holding the hinge. These are distinct versions; the printed weight alone does not make them directly comparable.
Muscles involved
Main involvement
Sides of the back (latissimus dorsi). Draw the upper arms towards the torso during the pull.
Between the shoulder blades (trapezius and rhomboids). Help guide and steady the shoulder blades as the arms move.
Supporting involvement
Front of the upper arms (biceps). Bend the elbows during the pull.
Palm-side forearm muscles. Maintain the grip on the bar, handle or dumbbells.
Back of the shoulders (posterior deltoids). Help draw the upper arms backwards.
Muscles along the back (spinal erectors). Help maintain the torso position while the arms row.
Explore these muscle regions in 3D
This optional anatomy view shows the named muscle locations. Use the real demonstration and written tutorial above for technique.
Sources and video credits
The demonstration is published by PureGym and remains hosted by its publisher on YouTube.
SG Home Wellness provides the written tutorial using the sources below. Setup, finishing steps and modifications can extend beyond the clip. Controls on other equipment can differ.