SG Home
Wellness

Exercise tutorial

Barbell hip thrust

The barbell hip thrust raises and lowers the hips while the upper back rests against a stable bench. A bar rests across the hip crease and both feet remain on the floor. It is different from a floor bridge, where the shoulders stay on the ground.

Watch a real demonstration

How To Do A Barbell Hip Thrust

Demonstration by PureGym

Loading the player connects to YouTube. Use its controls to play, pause or view full screen.

Version demonstrated: Barbell across the hip crease with upper-back bench support and both feet on the floor.

Three things to notice

  • Locate the upper-back contact with the bench and the feet on the floor.
  • Follow the bar and hips rising together.
  • Compare the torso and pelvis as the hips lower again.

Written tutorial by SG Home Wellness. Setup, finishing steps and modifications also draw on the supporting sources; the clip may not show each of these actions.

Before you move

Equipment Barbell, suitable plates and collars, Secure bar pad if needed, Stable bench or box suitable for the movement, Level, non-slip floor.

Also called Bench hip thrust, Barbell glute hip thrust.

  • Check that the bench is stable, suitable for hip-thrust support and unable to slide or tip under pressure. The edge should support the upper back around the lower shoulder-blade area rather than press on the neck. Use a manageable bench height.
  • Rehearse without a bar. Sit on the floor against the bench, plant both feet and lift the hips slightly to find a comfortable supported position. Check that you can lower and get out again; a bench-supported floor transfer may need help or a different exercise.
  • Use a bar and plate diameter that allow a controlled approach to the hips. Load symmetrically with compatible collars and fit a secure pad if needed. Do not drag a heavy low bar over the knees or abdomen; get assistance with positioning if access is awkward.
  • With the bar resting across the hip crease, hold it steady with both hands and plant the feet in a repeatable position. Aim for a comfortable knee bend at the top, approximately shins upright, without treating a precise angle as mandatory. Keep the bench contact secure.

How to do the movement

  1. Prepare the supported position

    Keep the chin comfortably tucked rather than throwing the head backwards. Steady the trunk and bar, with both feet flat and the upper back supported.

  2. Lift at the hips

    Press through the feet to raise the pelvis and bar. Let the upper back pivot on its support. Stop when the hips reach your controlled extended position, without continuing into a large lower-back arch.

  3. Pause with the feet planted

    Keep the bar centred over the hip crease and the knees in line with the feet. The goal is a steady hip movement, not holding the highest possible position.

  4. Lower under control

    Bend at the hips to bring the bar down while keeping it steady with the hands. Return to a comfortable resting or near-resting bottom as your setup allows, and reset before lifting again.

Finish and get out of position

  • Lower the hips to a supported rest and let the plates settle. Keep control of the bar while arranging the planned roll-away or assisted removal; do not attempt to sit up against a trapped bar.
  • Move the bar clear only once it is supported and you have room to move the legs. Use the help you planned for access, then get up steadily and unload the bar evenly.
Exercise reference

Keep the key cue

Hip thrust — stable bench, bar at the hip crease and a controlled lift without a back arch.

This browser keeps a reminder and link to the full tutorial.

Cues to remember

Lift the hips, not the ribs

If the chest flares upwards while the pelvis barely moves, reduce range and practise the unloaded version.

Keep the bar centred

Hold the bar against rolling and check padding. Pressure on the abdomen or a bar repeatedly sliding needs a setup change.

Check the bench each time

A support that shifts is a reason to stop. Adding bodyweight or plates to an unsuitable bench is not a substitute for an appropriate setup.

Is the aim to arch my back as high as possible?

No. The task is hip extension with a steady trunk. Raising the ribs and leaning the head back can add movement elsewhere after the useful hip lift has finished.

What to watch out for

Bench slides or the neck becomes the support point
Stop and reset with a suitable stable support and manageable height. Do not continue just because the bar is already positioned.
Bar slides towards the abdomen
Lower to rest and check its hip-crease position, pad and hand control before repeating.
Arching the lower back to finish the lift
Reduce range and resistance, keep the trunk steadier and finish where the hips extend without an added backward bend.

Make it easier or build from this version

The handling task matters as much as the lift. Use your programme for workload and finish before the bar, bench or foot position becomes difficult to control. A painful pressure point or uncertain floor exit needs a different setup.

Make it easier

Bodyweight hip thrust

Remove the bar and keep the same stable bench contact and planted feet. Rehearse the rise, lower and floor exit before adding resistance.

Floor bridge with guidance

This is a different supported position with the upper back on the floor. It may simplify equipment handling, but floor access still needs to be manageable.

Read the floor bridge with guidance tutorial

Build from here

A small increase in bar load

Keep the same bench, foot position, pad and controlled range. Add load only when the setup and final removal remain manageable.

What can differ

A floor bridge keeps the shoulders on the ground and changes the range. A dumbbell or band changes how resistance is positioned. Bench heights and plate diameters affect access; copying a demonstrator’s load or foot distance does not establish a suitable setup for you.

Muscles involved

Main involvement

  • Buttocks (gluteus maximus). Extends the hips to raise the pelvis and bar, and helps control the lowering phase.

Supporting involvement

  • Back of the thighs (hamstrings). Contribute to hip extension and control of the hip-bending phase.
  • Front of the thighs (quadriceps). Help maintain the planted-foot and bent-knee position as the hips move.
  • Muscles alongside the spine (spinal erectors). Work to maintain a steady trunk while the load is supported.
  • Abdominal muscles. Help steady the trunk while the legs and hips move.
Explore these muscle regions in 3D

This optional anatomy view shows the named muscle locations. Use the real demonstration and written tutorial above for technique.

Sources and video credits

The demonstration is published by PureGym and remains hosted by its publisher on YouTube.

SG Home Wellness provides the written tutorial using the sources below. Setup, finishing steps and modifications can extend beyond the clip. Controls on other equipment can differ.

The optional anatomy model has its own licence and attribution.

Coaching