A landmine holds one end of a barbell in a pivot while you row the loaded end with both hands. The bar follows an arc, while your hips and trunk hold a forward lean. This is free-weight barbell work with an anchor, rather than a chest-supported T-bar machine.
Written tutorial by SG Home Wellness. Setup, finishing steps and modifications also draw on the supporting sources; the clip may not show each of these actions.
Before you move
Equipment Barbell in an approved landmine pivot, Compatible two-hand row handle, Suitable plates and any required retainers, Clear floor space.
Also called Landmine row with handle, T-bar landmine row, Barbell T-bar row.
Use a purpose-built landmine attachment on a compatible secured rack or manufacturer-approved base. Confirm its pin, hardware and any required floor anchoring are fitted as instructed. The bar end must sit fully in the sleeve. Do not wedge an unprotected bar into a room corner or use loose plates as an improvised anchor.
Check that the row handle is compatible with the bar and load, and secured in its intended position. Use the product’s required plate retainers. A towel or loose rope is not the same as the demonstrated handle. Clear the full arc of the plates and keep other people away from the pivot and loaded end.
Start with a load you can lift into the hinge and return to rest. Straddle the bar only if your attachment and handle are designed for that stance. Place the feet steadily on either side, bend the knees and move the hips backwards until you can take both handles without reaching around the plates.
Grip securely with the thumbs around the handles. Lift the loaded end using the pickup you have learned, then settle a comfortable forward lean with the arms long. Keep the torso steady, neck following the trunk and enough room between the plates and your body. Ask for instruction if the pickup or handle fit is unfamiliar.
How to do the movement
Let the arms reach along the arc
Hold the handle beneath the torso with both feet grounded. Keep a modest knee bend and a steady hip lean. The bar pivots at the far end rather than travelling straight up and down.
Draw both elbows back
Pull the handle towards the lower ribs or upper abdomen as the elbows bend. Breathe out through the effort. Let the shoulder blades move with the arms without standing up to accelerate the plates.
Stop before contact becomes a collision
End the pull where the shoulders and torso remain comfortable and steady. Plate diameter, handle shape and body proportions can limit clearance. Do not force the plates into the chest to match somebody else’s endpoint.
Follow the same arc down
Lengthen the elbows and lower the handle smoothly towards its starting point. Maintain the hip lean and keep fingers clear of plate and handle pinch points. Begin another repetition from control, not a bounce.
Finish and get out of position
Lower the loaded end through the controlled arc until it rests on the designated floor or support, using your practised hip-and-knee bend. Keep both hands on the handle until the weight is fully supported. Do not twist sideways to drop it.
Once the bar is still, step clear and unload it using the attachment instructions. Do not reach into the pivot or remove a retaining part while the bar is loaded or moving.
Exercise reference
Keep the key cue
Landmine row — approved anchor and handle, steady hip lean and a smooth return to rest.
This browser keeps a reminder and link to the full tutorial.
Cues to remember
Anchor first, row second
A moving pivot base or lifting rack is a setup failure. Put the weight down and have the mounting checked.
Hold the hinge
The bar’s pivot does not support your chest. If you stand taller for every pull, reduce the load or use a chest-supported row.
Leave room for the plates
Stop at a comfortable endpoint with clearance. A bigger plate can shorten available travel even at the same printed load.
Is every T-bar row the same exercise?
No. A free bar in a landmine, a dedicated lever station and a chest-supported T-bar machine have different supports, handles and starting procedures. This page uses a mounted barbell and two-hand handle; do not borrow another machine’s release controls.
What to watch out for
The rack, pivot or bar sleeve shifts
Lower the weight to rest and stop. Have staff verify the correct compatible mounting and loading before continuing; adding more plates to the base is not a substitute for approved assembly.
The torso rises to launch the bar
Reduce the load and keep the same hip angle through pull and return. A more supported dumbbell row is an alternative if holding the hinge is the limiting task.
Plates hit the body or the hands catch near the attachment
Reset the handle, stance and comfortable endpoint with little load. Use only a compatible handle and keep fingers clear; do not push through repeated contact.
Make it easier or build from this version
Record the attachment, handle, plate load and any bar details needed to repeat the setup. There is no required path from two-hand rows to one-arm rows or unsupported heavier lifting. Stop for an unstable anchor, pinching contact or a hinge you cannot hold.
Make it easier
Less plate load on the same attachment
Keep the approved anchor, handle and foot placement while reducing the load. Check that you can still collect and replace the bar; even an unplated bar has weight.
Chest-supported dumbbell row
This changes the equipment and torso support. Use the full inclined-bench tutorial if you want to practise rowing without holding an unsupported hinge.
Keep the same handle, stance and endpoint while adding planned work. Stop before the hips begin driving the bar.
Add an appropriate plate increment
Keep the same approved mounting and recheck plate clearance and set-down. A larger-diameter plate may change the range, so compare the actual movement rather than load alone.
What can differ
A one-arm landmine row changes stance, grip and how you resist turning. Different two-hand handles change reach and the path of the elbows. A chest pad adds support absent here. Count bar and plate loading consistently on the same attachment: the pivot and hand position mean the number is not directly equivalent to a barbell bent-over row.
Muscles involved
Main involvement
Sides of the back (latissimus dorsi). Draw the upper arms towards the torso during the pull.
Between the shoulder blades (trapezius and rhomboids). Help guide and steady the shoulder blades as the arms move.
Supporting involvement
Front of the upper arms (biceps). Bend the elbows during the pull.
Palm-side forearm muscles. Maintain the grip on the bar, handle or dumbbells.
Back of the shoulders (posterior deltoids). Help draw the upper arms backwards.
Muscles along the back (spinal erectors). Help maintain the torso position while the arms row.
Explore these muscle regions in 3D
This optional anatomy view shows the named muscle locations. Use the real demonstration and written tutorial above for technique.
Sources and video credits
The demonstration is published by OPEX Fitness and remains hosted by its publisher on YouTube.
SG Home Wellness provides the written tutorial using the sources below. Setup, finishing steps and modifications can extend beyond the clip. Controls on other equipment can differ.